Full user manual for GigaPlus is linked below for download in PDF format.

Brief Table of Contents with page number

• Overview.. 17
• Ports and Indicators – Indoor Unit 19
• Ports and Indicators – Outdoor Unit 22
• Remote Mounting. 24
• Combiners for Antenna Sharing. 24
• Power Supply. 25
• Flexible Interfaces and Form Factor 26
• Traffic Capacity. 26
• Industry Leading System Gain.. 27
• Full Licensed band frequency and T/R spacing support 28
• Channel Sizes from 3.5 MHz to 80 MHz. 29
• Adaptive Coding and Modulation.. 29
• Link Protection through 1+1 Hot Standby. 30
• 2.0         
• Wireless Operation Detail 31
• Channel Bandwidth.. 31
• Modulation.. 31
• Mean Squared Error (MSE) 31
• Adaptive Coding and Modulation (ACM) 33
• Wireless Link Capacity. 36
• Automatic Transmit Power Control (ATPC) 37
• ATPC Max Power & Step Size. 37
• Transmitter Maximum Power Output 37
• Transmitter Minimum Power output 38
• Receiver Maximum Input 39
• 3.0         
• Network Operation Detail 40
• 1+0 Non-Protected Link Configuration.. 40
• 1+1 Hot Standby Protected Link Configuration.. 41
• Hardware triggered failover 42
• Software triggered failover 43
• User triggered (manual) failover 43
• Rapid Port Shutdown (RPS) 44
• VLAN Tagging. 44
• Port Mapping (802.1q) 45
• Q in Q/Double Tagging and smart_mode. 45
• Class of Service (802.1p) 46
• Port Priority. 46
• Port Rate Limiting (Ingress) 47
• 4.0         
• Link Management 48
• Overview.. 48
• Graphical User Interface (Web Browser) 49
• Command Line Interface (CLI) using SSH, Telnet or Console. 52
• Changing Password. 54
• Console Port 54
• Simple Network Management Protocol (SNMP) 55
• Common Objects for Monitoring and Control 56
• Firmware Upgrade. 57
• Upgrade Procedure -TFTP.. 58
• Upgrade Procedure -FTP.. 60
• Capacity Upgrades. 62
• 5.0         
• Link Planning. 63
• Frequency/Path Planning. 63
• Site Selection.. 63
• Licensing. 63
• 6.0        
• Installation. 64
• Safety. 64
• Installation Process. 67
• Preparing for Installation.. 67
• Tools. 67
• Grounding Overview.. 68
• Power Supply Installation.. 69
• Antenna Installation.. 70
• Install the IDU.. 70
• Connecting power 71
• Ferrite Installation.. 72
• 1+1 Hot Standby IDU Installation.. 73
• HP ODU Installation on Antenna. 74
• IF Cable Installation.. 76
• Weather Proofing Cabling. 78
• 1+1 Hot Standby ODU Installation.. 79
• 7.0        
• Link Configuration. 80
• Web Based Configuration.. 81
• Web Based 1+0 Setup. 81
• Web Based 1+1 Setup. 85
• Adaptive Coding and Modulation (ACM) (Optional) 86
• Automatic Transmit Power Control (ATPC) (Optional) 87
• Alarms, RPS and Telnet/TFTP Daemons. 87
• Ethernet Configuration.. 88
• Status Monitoring Overview.. 89
• System Status. 89
• Link Status. 90
• Ethernet Statistics. 91
• RF Statistics. 92
• T1/E1 Statistics. 93
• Diagnostic Options. 94
• Reset Config  94
• System Log. 95
• Config View.. 96
• User Settings. 97
• Command Line Interface (CLI) Based Configuration.. 98
• CLI Based 1+0 Configuration.. 98
• CLI Based 1+1 Hot Standby Configuration.. 104
• Antenna Alignment 105
• CLI Common Task Reference. 107
• Setting up the In-Band-Management (IBM) 107
• Capacity License Activation.. 109
• Automatic Transmit Power Control (ATPC) Configuration (optional) 109
• Check Ethernet and RF port Statistics. 110
• Enable Traps (Optional) 113
• 8.0         
• Troubleshooting. 114
• Symptom: No Link (Lock = 0 during linktest) 114
• MSE is too high and/or bit errors are showing when running linktest 114
• Receive Signal Level is too low.. 115
• RF Link is good but packet loss is occurring: 116
• No direct management using Out of band port 116
• No Radio Management connection over the link. 117
• T1/E1 Ports not passing traffic. 117
• Appendix A – Command Line Interface Reference. 118
• Appendix B – Product Specifications. 182
• Appendix C – Cable Wiring. 188
• Appendix D – MIB OID Listing. 192
• Appendix E – Part Numbers. 203
• Appendix F – Link Install and Commissioning Logs. 216
• Appendix G – Declaration of Conformity. 227
• Glossary. 228